Loading 3D model...

DC Power Distribution, 1U

ParamTweaks

Title

€19

Description

A 1U distribution panel for our 10-inch rack: two to eight panel-mount barrel jacks across the front, on a shallow box behind with threaded bosses for a bus bar or a distribution board.

DC only, and deliberately. We do not sell a printed enclosure for mains. That is a product-safety decision rather than something we have not got round to.

Choose: two to eight outlets and the jack bore — small or large.

In the box: the panel, four M4 heat-set inserts pressed before shipping, and four M4 x 10 screws.

You supply the barrel jacks and the bus bar or distribution PCB.

Related Products

A 1U DC distribution panel on a 190.5 mm plate: six barrel-jack bores across a shallow box, and room for eight

View Design →

DC Power Distribution, 1U, 7.5-inch

A 1U meter panel: a flat plate with three rectangular cutouts sized to panel-mount volt and amp meters, no venting

View Design →

Meter Panel, 1U

A 1U shelf for a small enclosed power supply, with four strap-down inserts in a floor vented with 5 mm hexagons on 8 mm centres and an open front for its leads, with front insert seats inside the end plates

View Design →

PSU Shelf, 1U

A 1U meter panel: a flat plate with 48 x 29 mm cutouts for panel-mount volt and amp meters, up to three across

View Design →

Meter Panel, 1U, 7.5-inch

A 1U shelf on a 190.5 mm bezel for a small enclosed power supply up to 125 mm across, with four strap-down inserts in a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates

View Design →

PSU Shelf, 1U, 7.5-inch

A 1U cable pass-through bar: two wide obround openings with a tie-off lip behind them

View Design →

Cable Pass-through Bar, 1U

A 1U shelf for a multi-port USB charger, with four strap-down floor inserts in a loose rectangle and a fixed port window sized to its own row of ports, over a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates

View Design →

USB Charger Shelf, 1U

A 2U tray for an SFX, SFX-L, TFX, Flex ATX or custom power supply, held down by two printed straps arching over the body, with a front window cut to the body’s own width, over a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates

View Design →

PSU Tray, 2U

A 1U keystone patch panel: eight port openings in a recessed front face, ribbed behind

View Design →

Keystone Patch Panel

A 2U mount bolted for an SFX or SFX-L power supply: a window for the fan and inlet face, with the supply’s own three screw holes cut through the bezel beside it, over a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates

View Design →

PSU Mount, 2U

A 7.5-inch 3U DC UPS mount with a single-piece bezel, four-bolt dock and removable carrier, on a floor vented with 5 mm hexagons on 8 mm centres

View Design →

UPS / SAI Shelf, 3U, 7.5-inch

A 7.5-inch 2U vertical board caddy with removable carriers and a single-piece bezel, on a floor vented with 5 mm hexagons on 8 mm centres

View Design →

Vertical Board Caddy, 2U, 7.5-inch

A 3U DC UPS mount with a four-bolt dock and removable OpenUPS2 carrier on a floor vented with 5 mm hexagons on 8 mm centres

View Design →

UPS / SAI Shelf, 3U

A 2U vertical board caddy with independent removable carriers on a floor vented with 5 mm hexagons on 8 mm centres

View Design →

Vertical Board Caddy, 2U

A 1U USB charger shelf: a fixed window for a row of ports, over a floor with strap inserts, vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates

View Design →

USB Charger Shelf, 1U, 7.5-inch

A 1U SBC tray with four mounting holes set to measured rectangular spacing on a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates

View Design →

SBC Universal Tray, 1U, 7.5-inch

A 2U PSU tray: a one-piece bezel with a window sized to the supply, over a floor vented with 5 mm hexagons on 8 mm centres, with two straps, with front insert seats inside the end plates

View Design →

PSU Tray, 2U, 7.5-inch

A 2U PSU mount: a one-piece bezel bolted for an SFX supply, with a window for its fan and inlet, over a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates

View Design →

PSU Mount, 2U, 7.5-inch

A 1U Raspberry Pi Zero cluster tray: two rows of two boards on a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates

View Design →

Raspberry Pi Zero Cluster Tray, 1U, 7.5-inch

A 2U Raspberry Pi blade tray: boards standing on edge between comb fins, each with its own bezel window, over a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates

View Design →

Raspberry Pi Blade Tray, 2U, 7.5-inch

A 2U NUC shelf: a one-piece bezel with a front window, over a floor vented with 5 mm hexagons on 8 mm centres, with two straps, with front insert seats inside the end plates

View Design →

NUC Shelf, 2U, 7.5-inch