Loading 3D model...

USB Charger Shelf, 1U

ParamTweaks
Title
Default Title
€29

Description

A 1U shelf for our 10-inch rack, strapped down for a multi-port USB charger, with a front window sized to its own row of ports.

Four floor inserts accept customer-supplied screw-down tie bases, at most 15 mm wide, for flexible straps over the measured charger. Choose tie-base screws for the stated insert engagement.

Measured port clearance. Set the charger body height to size its front opening; the selected unit must fit within 1U above the supporting floor.

What this is not: a power strip, and not a distribution panel. Nothing printed here carries voltage — the charger is the customer’s own certified unit, same boundary as our DC-PDU panel and PSU shelf.

Prints in two pieces: the bezel and floor. In the box: both pieces, twelve M4 heat-set inserts and eight M4 × 10 bezel screws. You supply the charger, tie bases, their screws and flexible straps.

Choose: charger body height, depth and floor venting.

Related Products

A 1U USB charger shelf: a fixed window for a row of ports, over a floor with strap inserts, vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates
View Design →

USB Charger Shelf, 1U, 7.5-inch

€28
A 1U shelf for a small enclosed power supply, with four strap-down inserts in a floor vented with 5 mm hexagons on 8 mm centres and an open front for its leads, with front insert seats inside the end plates
View Design →

PSU Shelf, 1U

€30
A 1U shelf on a 190.5 mm bezel for a small enclosed power supply up to 125 mm across, with four strap-down inserts in a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates
View Design →

PSU Shelf, 1U, 7.5-inch

€29
A 2U braced shelf: a floor vented with 5 mm hexagons on 8 mm centres between side walls that taper from full height at the front, with front insert seats inside the end plates
View Design →

Braced Shelf, 2U

€29
A 2U shelf for a NUC or thin client, strapped down by two printed straps arching over the body, with a front window cut to the body’s own width, over a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates
View Design →

NUC Shelf, 2U

€36
A 1U shelf for a desktop network switch: a port window cut to the body width, with two printed straps arching over where the switch sits, on a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates
View Design →

Switch Shelf, 1U

€32
A 2U braced shelf: a floor vented with 5 mm hexagons on 8 mm centres between side walls that taper from full height at the front, with a single unseamed bezel, with front insert seats inside the end plates
View Design →

Braced Shelf, 2U, 7.5-inch

€28
A 1U drive tray for one 3.5-inch drive, held by a printed strap over its top rather than by its holes, on a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates
View Design →

Drive Tray, 1U

€33
A 2U tray for an SFX, SFX-L, TFX, Flex ATX or custom power supply, held down by two printed straps arching over the body, with a front window cut to the body’s own width, over a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates
View Design →

PSU Tray, 2U

€40
A 1U meter panel: a flat plate with three rectangular cutouts sized to panel-mount volt and amp meters, no venting
View Design →

Meter Panel, 1U

€13
A 7.5-inch 3U DC UPS mount with a single-piece bezel, four-bolt dock and removable carrier, on a floor vented with 5 mm hexagons on 8 mm centresNew
View Design →

UPS / SAI Shelf, 3U, 7.5-inch

€41
A 7.5-inch 2U vertical board caddy with removable carriers and a single-piece bezel, on a floor vented with 5 mm hexagons on 8 mm centresNew
View Design →

Vertical Board Caddy, 2U, 7.5-inch

€40
A 3U DC UPS mount with a four-bolt dock and removable OpenUPS2 carrier on a floor vented with 5 mm hexagons on 8 mm centresNew
View Design →

UPS / SAI Shelf, 3U

€45
A 2U vertical board caddy with independent removable carriers on a floor vented with 5 mm hexagons on 8 mm centresNew
View Design →

Vertical Board Caddy, 2U

€52
A 1U SBC tray with four mounting holes set to measured rectangular spacing on a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates
View Design →

SBC Universal Tray, 1U, 7.5-inch

€25
A 2U PSU tray: a one-piece bezel with a window sized to the supply, over a floor vented with 5 mm hexagons on 8 mm centres, with two straps, with front insert seats inside the end plates
View Design →

PSU Tray, 2U, 7.5-inch

€38
A 2U PSU mount: a one-piece bezel bolted for an SFX supply, with a window for its fan and inlet, over a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates
View Design →

PSU Mount, 2U, 7.5-inch

€28
A 1U Raspberry Pi Zero cluster tray: two rows of two boards on a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates
View Design →

Raspberry Pi Zero Cluster Tray, 1U, 7.5-inch

€25
A 2U Raspberry Pi blade tray: boards standing on edge between comb fins, each with its own bezel window, over a floor vented with 5 mm hexagons on 8 mm centres, with front insert seats inside the end plates
View Design →

Raspberry Pi Blade Tray, 2U, 7.5-inch

€35
A 2U NUC shelf: a one-piece bezel with a front window, over a floor vented with 5 mm hexagons on 8 mm centres, with two straps, with front insert seats inside the end plates
View Design →

NUC Shelf, 2U, 7.5-inch

€35
A 1U meter panel: a flat plate with 48 x 29 mm cutouts for panel-mount volt and amp meters, up to three across
View Design →

Meter Panel, 1U, 7.5-inch

€13